Not all appliances and electronics have Tech Sheets or Fast Track publications. Training Manuals generally contain more in-depth servicing information and circuit explanations.
Live Screen Mode. Auto Screen Switchover Time. Alert Function. Alarm Input. Alarm Output. Alarm Output Duration. Motion Detection. Pre Alarm Setup Time. Post Alarm Setup Time. Off, 3, 5, 10, 20, 30sec. Area Setting Low, Standard, High.
Off, 5, 10, 20, 30sec. Do not use multiple plugs at once. The following are the specifications of the battery you are using now. Page 7: Chapter 1 Overview Chapter 1 Overview Alarm LED lights on when an event occurs. Page 11 Name Function Displays the play screen of one channel and the live screen small of another channel as a PIP screen. Displays one channel play screen and Selection Button Mode an channel live screen. Network LED Displays both network connection and data transmission conditions.
Page 13 Name Function Displays the play screen of one channel and the live screen small of another channel as a PIP screen. Displays one channel play screen and an 5-channel live screen.
Mode Displays one channel play screen and an 8-channel live screen. Press it for backup operation. MODE Selects split-screen. Page Chapter 2 Installation Chapter 2 Installation Page Installation Environment Setup 7. Use certified power cord only. For the products with an input ground, use a power plug that has a ground. High temperature inside or outside of the product may cause reduced life and deteriorated performance see graph 1 below , leading to a malfunction. The rack on which the DVR is mounted should not be sealed off.
And it also can allow air circulation through the vent. As in the figure to the right, we recommend the product should be stacked up with other DVRs or rack-mounting devices at a certain space or you install a vent system to accommodate airflow. Then you shall check if the following items are in it. If you contact the RTC battery while adding hard disks, the battery failure may happen. Page 23 2. Remove the cover from the product.
Remove the cover by first lifting its back part upward after sliding the cover slightly backward. There is a bracket bracket-HDD mounted on the right and left sides where you can mount the HDD, and you have to remove the screws that are holding the bracket that you want to mount an HDD onto.
Remove the bracket-HDD from the product by separating the power supply cable, signal transmission cable IDE cable , and fan cable then pulling it toward the center of the product to separate its fixed part from the bottom. Page 25 5. When mounting an additional HDD, the primary master has to be mounted. When adding one — Primary slave add one When adding two — Secondary master mount additionally on the top of the under the bracket that is empty bracket that has a built-in HDD Make sure that the bracket-HDD is mounted stably inside of the product, then connect the power supply cable, signal transmission cable IDE cable , and fan cable to the HDD.
Check if there is any problem with connector or wiring inside of the product for connecting and mounting then close the cover. Page 27 This can cause operation failures because it raises the temperature inside your DVR. Page 29 3. Remove the bracket-HDD A from the product by separating the power supply cable, signal transmission cable IDE cable , and fan cable then pulling it toward the center of the product to separate its fixed part from the bottom.
Remove the bracket-HDD B by lifting it up after removing the screws. Page 31 5. When adding one - Primary slave mount on When adding two - Secondary Slave mount the top of the bracket that Tighten cover mounting screws.
The left and right side each has 5 spots and back side ha s1 spot Caution Caution Page Chapter 4 Live Chapter 4 Live Off] will appear. Definition of Live Screen Mode SHR receives 16 live images and displays them in the following 9 modes as seen in the picture.
Zoom Function Zoom function enlarges the selected area to double size, and it is only available in the single mode. The user can add up to 2 HDDs to this product. Remove the bracket-HDD A from the product by separating the power supply cable, signal the HDD, and you have to remove the screws that are holding the bracket that you want to transmission cable IDE cable , and fan cable then pulling it toward the center of the product mount an HDD onto.
Check if there is any problem with connector or wiring inside of the product for connecting and mounting then close the cover. Tighten cover mounting screws. The left and right side each has 5 spots and back side ha s1 spot other devices Caution Definition of Live Screen Icon The Live screen icons display the current setup and function status of each screen.
This icon appears when the backup data is played. In addition, the channel being set to Audio On can Freeze function pauses the video image in the Live Screen, it is only available in the Live Mode. Please be sure to stop the backup before you delete a data. In the recording mode, suspend the recording and delete a data. Caution Caution [System Shutdown] The following protocols are now being supported. Off : Event Monitoring does not operate to turn to the screen where an event occurs.
The frame rate is number of the recorded scenes per sec- Pre-Event Section ond. Alarm Detection Setup Off : Sensor does not operate. O Normal Open Sensor : Sensor remains open all the time and if closed, an alarm will be issued. A Contact N. C Normal Close Sensor : Sensor remains closed all the time and if open, an alarm will be issued.
Sensitivity grade consists of Low Medium Very High in the ascending order. Select an alarm-out that you want to synchronize with the current motion channel. Multi-selection is possible. Select a date, time, and camera No. This is a very special function.
0コメント